maximum permissible error of a lpg fuel dispenser as per legal metrology general rules 2011

Arizona Administrative Code

A person that owns or operates a motor fuel dispensing site or transmix or production facility outside the CBG covered area shall ensure that a motor fuel offered for sale at the motor fuel dispensing site or transmix or production facility meets all the appropriate specifications in R20 2 702 except that from May 1 through September 30

Weights and Measures Regulations 1999 Legislation

  (c) measuring systems (other than LPG dispensers) for liquefied gases under pressure measured at a temperature equal to or above −10°C, and LPG dispensers for motor vehicles, are class 1.0: (d) measuring systems included in paragraph (a) or paragraph (b) are class 1.0 when used for liquids with the following properties:

The Legal Metrology (Packaged Commodities) Rules, 2011

The Legal Metrology (Packaged Commodities) Rules, 2011. NOTIFICATION . 7th March 2011 . GSR 202 (E) In exercise of the powers conferred by sub section (1) read with clause (j) and (q) of sub section (2) of section 52 of the Legal Metrology Act 2009, (1 of 2010), the Central Government hereby makes the following rules, namely: 1.

102. Transport Industry and Warehousing ILO Encyclopaedia

The flow rate of outside air within an aircraft cabin can vary from as little as 0.2 m 3 per minute per person to m 3 per minute per person, depending upon aircraft type and age, and depending on location within the cabin. New aircraft use recirculated cabin air to a much greater degree than do older models.

US8183995B2 Systems and methods for modifying power

Systems and methods for providing energy management utilize wireless wide area network broadcast signals and a decentralized receiver architecture to allow customers to make informed choices with regard to energy consumption and load shedding for particular appliances. A receiver assembly embedded within an appliance receives a broadcast signal, e.g., an FM subcarrier signal, including

Standards of Weights and Measures (General) Rules, 1987

Preliminary. Short title and commencement.—(1) These rules may be called The Standards of Weights and Measures (General) Rules, 1987. (2) They shall come into force on the date of their notification in the Official Gazette. Definitions.—In these rules, unless the context otherwise requires,— (a) “Act” means the Standards of Weights and Measures Act, 1976 (60 of 1976);

The Legal Metrology (General) Rules, 2011

The Legal Metrology (General) Rules, 2011 Rules regarding Weights, Measures, Weighing and Measuring Instruments Rule 11, 12 13 and 14. Every Weight, Measure, Weighing and Measuring Instrument used or intended to be used in. in any transaction, or; for protection

Malawi Diagnostic Trade Integration Study (DTIS) Update

Malawi Diagnostic Trade Integration Study (DTIS) Update Reducing trade costs to promote competitiveness and inclusive growth Prepared for the Enhanced Integrated Framework

Chapter 296 46B WAC:

(4) Electrical wiring or equipment subject to this chapter must be sufficiently accessible, at the time of inspection, to allow the inspector to visually inspect the installation to verify conformance with the NEC and any other electrical requirements of this chapter with the exception of not more than 8 feet of electrical conduit in a foundation of a one or two family dwelling or residential

oiml_bulletin_october_2014 SlideShare

  Maximum permissible errors. 9.3 Metrological requirements Accuracy classes according to OIML R 107: 0.2, 0.5, 1 and 2 (only in exceptional cases). Minimum capacity, Min: Smallest discrete load that can be weighed automatically. Overload: The actual maximum discrete load

Legal Metrology (Packaged Commodities) Rules, 2011

  In this article, Kanishka Chakraborty pursuing M.A, in Business Law from NUJS, Kolkata discusses Fundamentals of the Legal Metrology (Packaged Commodities) Rules, 2011. The Legal Metrology Act, 2009 came into effect from the 1 st of April, 2011, replacing the Weights and Measures Act. The Act was passed with the purpose of establishing and enforcing standards of weights and

Verification of auto LPG Dispensers

Part IV of the Eighth Schedule, The Legal Metrology (General) Rules, 2011 Specific provision: Part 2 Rule 5(7) The type of LPG used as a motor vehicle fuel is a liquid mixture containing at least 90 percent propane, 2.5 percent butane and higher hydrocarbons, and the balance is ethane and propylene.

Regulatory Framework, Safety Aspects, and Social

One practical example of legal metrology is the assurance that a hydrogen fuel dispenser at a public fueling station accurately tracks the hydrogen fuel mass transferred to a customer's hydrogen fueled vehicle, thus ensuring proper customer monetary charging. Key Relevant Attributes of Metrology

02 S&T General Scales & Other NIST

Thus, Dresser Wayne supports maintaining item 301 4 G A.6. as a Voting item at the National Conference on Weights and Measures in July 2010 and noted that it is in the best interest of the general public, station owners and the fuel dispensing industry in general. A complete copy of the letter can be viewed in Appendix A of this Report.

Dispensers with flow rates greater than 15 gallons per minute shall use a 30 micron or smaller nominal pore size filter. Dispensers with flow rates less than or equal to 15 gallons per minute in the following states may use a 30 micron or smaller nominal pore size

New Mexico Building Code PDF Free Download

All references in the IBC to the international fuel gas code are deemed references to the NMMC or the LPG standards, NMAC and NMSA 1978 70 5 1 et seq., collectively. Gas piping, systems and appliances for use with liquefied propane gas (LPG), or compressed natural gas (CNG), shall be governed by the LPG standards. (c) 101.4.3 Mechanical.

Specifications and Tolerances (S&T) Committee 2019 Interim

Example: If a belt conveyor scale system has a maximum rated capacity of 200 tons per hour (tph), and the normal use flow rate is 150 tph (75 % of the maximum rated capacity), no testing at additional flow rates is required provided the flow rates remain above 140 tph for more than 80 % of the time.

Annexes to COM(2011)769 Harmonisation of the laws of the

For instruments where it is possible to pre set a fill weight; the maximum difference between the pre set value and the average mass of the fills shall not exceed 0,312 of the maximum permissible deviation of each fill from the average, as specified in Table 5.

S.I. No. 160/2007 Legal Metrology (European Conformity

1. These Regulations may be cited as the Legal Metrology (European Conformity Assessment of Measuring Instruments) Regulations 2007, and shall come into operation on the making thereof. Interpretation. 2. In these Regulations— ‘Act’ means the Metrology Act 1996 (No. 27 of 1996);

WEIGHTS AND MEASURES REGULATIONS TABLE OF

WEIGHTS AND MEASURES REGULATIONS TABLE OF PROVISIONS Regulation PART I PRELIMINARY 1. Citation 2. Commencement 3. Definitions 2 stroke fuel dispensers 87. Tolerances for 2 stroke fuel dispensers "tolerance" means the maximum permissible departure in